3V LVDS QUAD CMOS DIFFERENTIAL LINE DRIVER

National Semiconductor Europe Fax: Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. This part can be operated from 3. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. The enables are common to all four drivers.

Uploader: Mell
Date Added: 22 April 2007
File Size: 38.96 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 67873
Price: Free* [*Free Regsitration Required]

Driver Channel 2 Logic Input. Channel to Channel Skew is defined as the difference between the propagation delay of the channel and the other channels in the same chip with any event on the inputs.

AC specifications for the driver are a tenfold improvement over other existing RS drivers. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Product device recommended for new designs.

The termination resistor converts the current sourced by the driver into a voltage that is detected by the receiver. On the printed circuit board, this distance should remain constant to avoid discontinuities in differential impedance. Output short circuit current IOS is specified as magnitude only, minus sign indicates direction only. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause diffsrential failure of the life support device or system, or to affect its safety or effectiveness.

  DELL E196FP MONITOR DRIVER

If the cable picks up more than 10mV of differential noise, the receiver may see the noise as a valid signal and switch. The information provided on this page represents TI’s knowledge and belief as of the date that it is provided.

Other configurations are possible such as a multireceiver configuration, but the effects of a mid-stream connector scable stub sand other impedance discontinuities as well as ground shifting, noise margin limits, and total termination loading must be taken into account. They are not meant to imply that the devices should be operated at these limits. The internal circuitry will guarantee a high, stable output state. All input voltages are for one channel unless otherwise specified.

Only one output should be shorted at a time, do not exceed maximum junction temperature specification.

Twisted pair cable will offer better balance than flat ribbon cable. LVDS will not work without resistor termination. Except where mandated diffefential applicable law, testing of all parameters of each component is not necessarily performed. One Technology Way, P. Typically the characteristic impedance of the media is in the range of X.

Other inputs are set to GND. The current mode driver provides substantial benefits over voltage mode drivers, such as an RS driver. Ckos ensured specifications and test conditions, see the Electrical Characteristics.

3 V, LVDS, Quad, CMOS Differential Line Driver ADN

Keep drivers and lgds as close to the LVDS port side connectors as possible. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.

  LDD-1000H LED DRIVER DOWNLOAD

Note that because the differential voltage reverses polarity, the peak-to-peak voltage swing across RT is twice the differential voltage. These inputs control all four drivers and turn off the current outputs in the disabled state to reduce the ,ine power consumption idfferential typically 10 mW.

All voltages are referenced to ground unless otherwise specified. AC parameters are guaranteed by design and characterization. Device has been announced but is not in production. Single-Ended Driver Output Voltage vs. Life support devices or systems are difverential or systems which, a are intended for surgical implant into the body, or b support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user.

DS90LV032 3V LVDS Quad CMOS Differential Line Receiver

Enable Inputs Truth Table Current-mode drivers offer considerable advantages over voltagemode drivers such as RS drivers. Do not pvds solely on the auto-route function for differential traces. The received voltage is centered around the receiver offset of 1. The receiver is connected to the driver through a balanced media which may be a standard twisted pair cable, a parallel pair cable, or simply PCB traces.